top of page

Structural plaster, ready to use. Orange peel. For interior and exterior use.

Usage technology:

1 layer - Base

2nd layer - Deep penetration impregnation primer

3rd layer - Putty

4th layer - Quartz soil

5 layer - decorative finish

6 layer - Facade paint

7 layer - Protection over plaster

Technical description:

Type of material:

For decorative finishing of facades, as well as indoors in places with increased operational load (walls of flights of stairs and landings, halls, offices, corridors, etc.). Provides a rough orange peel finish with an even grain.


Water, synthetic acrylic dispersion, titanium dioxide, fillers, additives, preservative.




1.88 g / cm3

Grain size:

2.0 mm,


metal spatula, plastic spatula.


Convenient to apply, easy to process, has high adhesion to the base. The resulting coating is weatherproof, resistant to climatic influences and aggressive industrial air pollution, resistant to mechanical stress, with high elasticity and moisture resistance, has good vapor permeability.

Substrate preparation:

The surface must be clean, dry and sound, free of grease. Smooth uneven surfaces with Kaizer Fassadenspachtel or Fix Finish (for interior use).


Before applying the plaster to the substrate, the surface must be treated with Kaizer's Quarzgrund quartz primer. If the plaster is tinted, it is recommended to tint it in the same color and primer. Highly absorbent surfaces of aerated concrete, asbestos cement, gypsum, etc., as well as crumbling unreliable surfaces should be treated with the Kaizer brand Putzgrundharter 1: 4 primer.

Mix the contents of the bucket thoroughly (without beating). Apply with a stainless spatula to the base from bottom to top. Remove excess plaster to the thickness of the granule. Immediately or no later than 10 minutes (depending on temperature), apply the desired texture with a plastic trowel.


Dye Vollton und Abtönfarbe from Kaizer in a maximum ratio of 2%. For richer tones, you can order the delivery from the factory or apply plaster without adding dye, and then paint with tinted dispersion paint.

Tool cleaning:

Immediately after use with water. Hold the instruments in the water during the pause.


In a cool, frost-protected place, in a tightly closed container for 12 months.


Plastic bucket 15 and 30 kg


Grain 2.0 mm - approx. 3.0 kg / m2

For an accurate calculation of the consumption, we recommend conducting a test coating on site.

Drying time:

At a temperature of +20 ° C, a hard shell forms within 30-60 minutes. Under normal conditions, complete hardening takes 2-3 days. High humidity and cold substrates (especially for exterior walls) can delay drying. We recommend that you pay special attention to this during the cold season.

Temperature range:

Air and substrate temperature during application and drying is not lower than +5 ° С.


The plaster, like all dispersion products, should not be applied in direct sunlight. Make sure that during operation the temperature of the air and the substrate is not lower than +5 ° C. Fillers and granulators of natural origin are used for the production of plaster, therefore slight fluctuations in color are possible. Based on this, it is necessary to use material with the same batch number when plastering one object.


Keep out of the reach of children. Do not inhale vapors when spraying. Ventilate well during and after handling the product. In case of contact with eyes or skin, rinse immediately with plenty of water. Do not empty into drains, waterways or soil.


According to local regulations

Decorative plaster - Kratzputz Lux 2,0 mm

1 Kilogram
    Логотип 110.png

      Казахстанский лакокрасочный завод "KAIZER"  

      Смотреть адреса магазинов "KAIZER" по Казахстану

             +7 (727) 347-08-53 

             +7 (701) 952-64-89.

    bottom of page